Posts Tagged Chicago Fire Department apparatus history

A commentary: CFD apparatus history – part 1 of 3

A question was posed to Bill Post from Mike McAuliffe:

Bill, … on the subject of Snorkels, perhaps you could provide some insight as to why Fire Commissioner Quinn was so tight with funds, that he did not purchase a new small Snorkel for SS-3 or a new Snorkel for Snorkel 1 (which became SS-3), and, most importantly, he did not purchase a new Snorkel to replace Snorkel 7?

The Snorkels were his obvious pride and joy, though in my opinion, [this was] to the extent that he was blinded to the potential advantages of [the] Aerialscope/tower ladders. Why didn’t he purchase replacements? This was during a time when Snorkels were fairly common. Some departments were even using small Snorkels as a second-piece engine. Crown was making superb Snorkels on the west coast. The LACityFD had two that they wanted to get rid of. It could not have been that difficult to get a good deal on a used or even a new one.

I always thought it was a mark against Quinn that the city had only one Snorkel on the south side; Snorkel 3, for most of the 1970s when the south side was “really rolling”. Whenever a south side still and box came in, you would always hear on the sounder, “Snorkel 5 to Snorkel 3?.

Thanks in advance for any replies.

 

Mike, you hit it right on the button. Money was indeed a problem for the Chicago Fire Department in the 1960s. That was one of the reasons why during the early 1960s until late 1966 through early 1967, the Chicago Fire Department only purchased unique or what would be called “specialty apparatus”. As you know, that was basically the Magirus 144-foot and 100-foot aerial ladders, Snorkels, Snorkel Squads, Fog Pressures, the original helicopter (441), jet (rescue) boats, plus of course ambulances and chief buggies.
The Chicago Fire Department was desperate for capital funds. The City of Chicago finally had to go to the voters during 1966/67 with a campaign to get their approval to be able to float a bond issue in order to be able to get a funding mechanism to invest in much needed city infrastructure, which included new fire engines. I even remember that there was a special half-hour long television special one evening (probably on Channel 9) that was about the need for the Chicago Fire Department to acquire new apparatus. Some of our equipment, like a number of the tractor-trailer hook and ladders went back to the 1920s. Commissioner Robert J Quinn was on the show doing an interview where he had said “I don’t see how the hell the voters could keep us from getting new fire apparatus” which was desperately needed.
The bond issue was passed. As far as Snorkel Company 1 goes, Commissioner Quinn had felt a need for a new Snorkel Squad company on the busy West Side, so he converted Snorkel 1’s rig into Snorkel Squad 3, and he purchased three Fog Pressure Wagons on longer chassis to be used as the new second pieces for the three Snorkel Squads. Snorkel Squad 3 went into service on May 16th, 1965 at the fire house at 2858 W. Fillmore. This had been the quarters of Engine 66 and Squad 7.
Engine 66 was relocated to Engine Company 44 and Squad 7 was taken out of service on that day. By the way, another major reason why the CFD didn’t purchase a new Snorkel 1 (besides the money) is for another very elemental reason; there was no space for any new Snorkels on the West Side. As an example, in order for Snorkel Squad 3 to go in service, they had to move Engine 66 and take Squad 7 out of service. At the time, Squad 7 was one of the two busiest squad companies in the city, so Commissioner Quinn figured that he would just replace it with a more modern and well-equipped Snorkel Squad. This made a lot of sense. The other of our “top 2″ squad companies was Squad 3, which had been located with Engine 61. At that time, they were at 54th and Wabash which was only a mile and a half west of Engine 60, Truck 37, and Snorkel Squad 2 in their new station. One of the reasons why Squad 3 stayed in service is because Snorkel Squad 2 was in a new station with plenty of room.  This wasn’t the case though on the West Side. Part of Commissioner Quinn’s reasoning to put Snorkels 4 through 7 in service in 1961 and 62 was because he wanted one Snorkel located in each of the seven Fire Divisions at the time.
Snorkel Company 1 was the smallest of the Snorkel companies (only 50 feet) so they were moved from Engine 50 (on the south side in the 4th Division) to Engine 109 (in the 2nd Division on the west side). The reason for the move was that the only fire station in? the 2nd Division that had (barely) enough room for a Snorkel was Engine 109’s house. The space that Engine 109 had for Snorkel 1 was minimal at best because you need to remember that Engine 109 was in a two-bay station and that one of the bays had Truck 32. The truck had a 1954 FWD tillered aerial ladder which had an 85-foot wooden ladder with a long rear overhang. Since Snorkel 1 was only 50 feet and didn’t have a long front over hang, they were the only Snorkel that could fit into Engine 109’s quarters.
During the early 1960s when most of the Snorkels were put in service, the south side wasn’t that much better then the west side when it came to having fire stations which were large enough to accommodate Snorkels. At the time, there were three fire divisions on the south side. They were divisions 4, 5, and 7.
Division 5, on the far southeast side, had room for Snorkel 6 at Engine 46’s house because they had two exceptionally large apparatus bays. The 7th Division, covered the far southwest side, (including Englewood), and included Battalions 29, 31, 26, and 12. Only Engine 84’s house was large enough and it was located at Halsted south of 57th Street which was only two blocks south of the 4th Division’s southern boundary line on Garfield Boulevard.
Snorkel 3 was relocated there after being moved from Engine 50’s house where they had replaced Snorkel 1 for roughly 6 months. It was a very tight fit in Engine 50’s house. They ended up exchanging Light Wagon 3 (at Engine 84) for Snorkel 3. After Snorkel 3 was relocated into the 7th Division from the 4th Division in 1962, there was no Snorkel assigned to the 4th Division from March 24, 1962 until October 28, 1964. When Engine 28’s new house was opened, they were finally able to move Snorkel 2 there. Before Engine 28’s new station was opened, Snorkels 2 and 4 were located less then a mile apart from May 6, 1961 until October 28, 1964. Snorkel 2 was with Engine 5 and Snorkel 4 was with Engine 25 at the Fire Academy. That lasted for over three years and it was due to a lack of adequate space to accommodate the Snorkels in many of the fire stations around the city.

This is part one of a three-part article.

Tags: , , , , , ,

Vintage Pirsch ad with CFD

In this reprint from a September, 1953 issue of Fire Engineering Magazine, the Peter Pirsch & Sons Co. of Kenosha, WI highlights 50 years of building fire engines for the Chicago Fire Department. The ad states that they started with 27 Pirsch Horse Drawn Wagons built in 1907, then there were 3 Pirsch equipped motorized chemical and hose cars in 1912 (the first motorized apparatus in Chicago), followed by 2 Pirsch equipped 600-gallon pumpers in 1916, and then 15 Pirsch 1,000-GPM 2-door cab pumpers built in 1953.

Peter Pirsch & Sons Co ad from 1953 Fire Engineering Magazine

Bill Friedrich collection

Tags: , , , , , , , , , , , ,

CFD Apparatus History – Fog Pressure Units

In response to a question about the use and purpose of the Fog Pressure Units that were deployed by the Chicago Fire Department in the early 1960s, Bill Post has provided the following historical commentary;

The purpose of the Fog Pressure was to be able to get an effective stream of water on the fire quickly before a conventional engine company could get hooked up to a hydrant and led out with a canvas line. They were also handy on expressways and in tight access areas such as alleys, near railroad embankments, and in areas with poor hydrant coverage and water supply problems.

When the Fog Pressure Units were purchased and put in service between 1961 and 1966, the Chicago Fire Department had only about 11 or 12 engine companies which had booster tanks. The CFD had gone literally for ten years (1955 to 1966) without purchasing any new engines. Only the last batch of engines that had been purchased which were ten 1956 B (cab model) pumpers were equipped with 200-gallon booster tanks. One or two older model engines had been modified by the shops and had similar booster tanks added, but they were exceptions to the rule.

The Fog Pressure Units were equipped with 300-gallon water tanks and two booster reels of narrow diameter hose. They had special fog (gun style) nozzles that produced fine misty streams of water at high pressures. This is why it was called “Fog”.  With the exception of the first unit which was built on a “Willys” Jeep chassis with a John Bean pump, all of the other Fog Pressure Units were built on International Harvester chassis with Darley pumps and bodies.

While a few of the Fog Pressure Units were located near some expressways, most of them were located in your busy high fire volume districts on the west and south sides. Fog Pressure 2 was located at O’Hare Field using the original Willy’s Jeep apparatus.

Fog Pressure Units were also assigned as the second pieces to all three of our Snorkel Squad companies as they allowed the Snorkel Squad men some tactical flexibility. These were also used to carry additional men and equipment. In 1964/65, the CFD had purchased three Fog Pressure Units that had longer bodies than the previous Fog Pressure rigs. These were specifically for the use of the Snorkel Squad companies.

When the fire department started getting new engines put into service in 1967, most of which were equipped with 500-gallon booster tanks, the CFD started relocating some of the Fog Pressure Units away from stations that were getting the new engines assigned to them. They also started taking them out of service so that by 1970 all of the Fog Pressure companies were gone with two exceptions. Fog Pressure 2 remained at O’Hare Field and of course they kept the Fog Pressure (SS1A) which was assigned to Snorkel Squad 1. Most of the Fog Pressure units were taken out of service in 1968 and 1969 which includes the ones that were assigned to Snorkel Squads 2 and 3 as both of those companies were decommissioned in 1969 as well.

As described in the previous post, Fog Pressure 31A was temporarily put in service at Truck 31’s new house (at the time) for a little over a year as a stop gap measure until Engine 64 was relocated into the house.

At their height in 1966 and 1967, we had twelve Fog Pressure companies in service (not including the three assigned to the Snorkel Squads) but within 2 years nearly all of them were out of service with the above mentioned exceptions.

Bill Post

Tags: , , , , ,

CFD Apparatus History – trucks with boosters 1967

The Chicago Fire Department purchased aerial ladder trucks with booster tanks and pumps for several years. Beginning in 1967 and spanning through 1973, 21 aerials were delivered from different manufacturers with water on-board. One of these was a mid-ship aerial and the balance were rear-mounts. Units were built by Seagrave, Pirsch, Ward LaFrance (Grove), and American LaFrance.

This is the first of several posts that will highlight the progression of these truck companies in Chicago.

In 1967, Chicago received two Seagrave mid-ship aerials…

… one was a straight truck (assigned first to Truck 44 and then to Truck 60) and the other (Shop #E-166) had a 60-GPM pump and carried 200 gallons of water. This unit was originally assigned to Truck 26, and then to Truck 31.

Chicago Fire Department Truck 31 1967 Seagrave mid-ship aerial with booster tank

Chicago received this 1967 Seagrave aerial that was assigned as Truck Company 26 and then Truck Company 31 (as lettered here). It had a 60-GPM pump and 200 gallons of water. Jack Connors photo

When Truck 31 moved into the house at 77th and Pulaski, there was no engine company with them. They were assigned a fog pressure unit as Truck 31A on November 17, 1971 until Engine 64 was located with them on March 12, 1973.

Chicago Fire Department Truck 31A 1966 International CargoStar Darley Fog Pressure unit

Chicago Truck 31A, a 1966 International/Darley Fog Pressure Unit was assigned to Truck 31 until Engine 64 was located with them at 77th and Pulaski in March of 1973. Jack Connors photo

Chicago Fire Department 1967 Seagrave mid-ship mounted aerial

Shown here many years later as Reserve Truck 7 is the 1967 Seagrave mid-ship aerial without a pump. Larry Shapiro photo

 

Tags: , , , , , , , ,

CFD Apparatus History – Ward LaFrance (1967)

In 1967, the Chicago Fire Department was badly in need of new engines. They looked to Ward LaFrance for assistance in acquiring what they had available. Chicago received four engines. One was assigned to Engine 42 (D-327) with a 1,000-GPM pump and 500 gallons of water. (this would later be re-assigned to Engine 46)

Chicago Fire Department history Ward LaFrance 1967 Engine

Engine 42 was assigned this 1967 Ward LaFrance with a 1,000-GPM pump and 500-gallon tank. Initially, the unit numbers were fairly small on the driver's door. George Brown collection

Chicago Fire Department history Ward LaFrance 1967 Engine

The officer's side of Engine 42's 1967 Ward LaFrance engine when it was delivered. Jack Connors photo

Chicago Fire Department history Ward LaFrance 1967 Engine 46

Shop #D-327 was later reassigned to Engine Company 46. Large company number decals were added to the engine. Jack Connors photo

The other three units were delivered with 1,250-GPM pumps and 350-gallon water tanks and were assigned to Engine 34 (D-332), Engine 54 (D-333), and Engine 11 (D-334).

Chicago Fire Department history Ward LaFrance 1967 Engine 34

Engine 34 received one of three 1967 Ward LaFrance pumpers with the larger 1,250-GPM pump and a smaller water tank. This image was taken after the shops added white decals that made the company unit number easier to read. Jack Connors photo

These units differed from the first piece that went to Engine 42. The body is taller, the pump panel has a polished backing instead of being painted and there are no flood lights. The cab has several different features including an extended bumper with a bell, siren, and front intake. The cab face underneath the windshield is covered with a panel to protect the paint from being scratched. Additionally, the rear of the cab canopy has a completely different shape than the earlier and subsequently later styles as well.

Chicago Fire Department history Ward LaFrance 1967 Engine 54

This shot of Engine 54 shows the officer's side of the 1,250-GPM series engines from 1967. Jack Connors photo

Shop #D-333 which was originally assigned to Engine 54 was later assigned to Engine 99 and then again to Engine 107. Unlike the other 1,250-GPM engines, this rig was delivered with one flood light.

Chicago Fire Department history Ward LaFrance 1967 Engine 98

CFD Shop #D-334 was originally assigned to Engine 11 and then to Engine 98 as shown here. Note also the CFD scramble on the lower portion of the driver's door and the company number under the windshield. Jack Connors photo

Chicago Fire Department history Ward LaFrance 1967 Engine 107

CFD Shop #D-334 was assigned for a third time to Engine Company 107. The hard suction trays have been raised to accommodate hose storage on the shelf above the lower compartments. Jack Connors photo

Tags: , , , , , , , , , , , , , , , ,